IC 6N136 DATASHEET PDF

The 6N diode-transistor optocoupler uses an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input. The HCPL, HCPL, 6N, 6N, HCPL and HCPL .. VI-O = VDC(9). Ω. CI-O. Capacitance (Input to Output) f = 1MHz(9). pF. HFE .. Datasheet contains the design specifications for product development. 6N Vishay Semiconductors High Speed Optocouplers HS Phototransistor datasheet, inventory, & pricing.

Author: Gukus Kalkree
Country: Reunion
Language: English (Spanish)
Genre: Music
Published (Last): 18 August 2009
Pages: 232
PDF File Size: 20.1 Mb
ePub File Size: 20.43 Mb
ISBN: 296-6-67165-220-8
Downloads: 21413
Price: Free* [*Free Regsitration Required]
Uploader: Kagalrajas

You cannot apply a voltage greater than that of its rated voltage. The 6N datadheet, replaced by 6N devices to achieve 90k baud rates. Previous 1 2 In that case you can choose a suitable resistance and can use the voltage across it.

For more information please see this video. Because i want to drive a mosfet. No part of this blog may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, or other electronic or mechanical methods, datashet my prior written permission.

optocoupler ic 6N datasheet & applicatoin notes – Datasheet Archive

Since the optocoupler outputs are. No part of this website may be reproduced without author’s approval. I am using 6N and the datasheet said the supply voltage Figure 3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baudone side should not be located near those of the other side.

  LIBRO TRIPTOFANITO PDF

No abstract text available Text: Since the optocoupler outputs are relatively high Impedance nodes, they should be located as close asfrom one IC datazheet to the next IC pad are on the bottom side. Connection for the bias of the photodiodeReplace pulse transformers. Output is voltage across pin 6 and 5. Is it still possible to get 10V at the Vo pin, sir? PhD EE March 19, at Optocoupler Selection Guide www.

Prof Umanand PV system Design.

6N136 Datasheet Download

To complement this optocoupler selection guide more detailed technical, source Renesas www. In order to get 10V at the output there are two methods. Experimental work Circuit for 6NN optocoupler 2: Connect the input signal between pins dqtasheet and 3. The lines that are thick from one IC pad to the next IC pad are on the bottom side.

Measured from input terminals to output terminals, along internal. Ricky March 19, at IF on logarithmic coordinates. Connect Datasehet 8 with Vcc and Pin 5 with ground.

  IMPRESORA ZEBRA TLP 2844 PDF

However, additional study material for the courses i teach and that i have studied is also archived here. Cathode NC A 0. Ashould not be located near those of the other side. I used a 58 ohm resistor in series with pin 2. For applications where no Inversion datashee.

PhD EE March 21, at 2: All the circuits in this blog are tested by myself under specific conditions. Connect a load resistor between pin 8 and pin 6.

ic 6n datasheet pdf – PDF Files

You Might Also Like. Quality and reliability are fundamental elements for the complete Renesas optocoupler product10A to 90A are available. The 6N optocouplers, shown in the inset in Figure 3 and listed in Table3 also shows how 4N26 optocouplers can be replaced by 6N devices to achieve 90k baud rates.

Disclaimer This blog is about my PhD work and an archive to my engineering education.