Here you can download and print out user manuals for Bosch power tools, not only for current tools but also for tools that are no longer available on the market. Royzee: Ok, It sounds like the lock has broken. This has a solenoid in it which keeps the door locked for several minutes after the final spin. Genuine BOSCH WASHING MACHINE Spares Parts, Every Part, Every Model, Search more then Appliance Parts, Free Delivery WFBAU

Author: Vushicage Nilar
Country: Eritrea
Language: English (Spanish)
Genre: Software
Published (Last): 15 January 2009
Pages: 310
PDF File Size: 16.77 Mb
ePub File Size: 9.7 Mb
ISBN: 924-5-60992-609-3
Downloads: 79117
Price: Free* [*Free Regsitration Required]
Uploader: Bakasa

I tried to used it again to finish the job, but it bogged down and ran in reverse. I am unable to get my table to lock into place. Bearing Help Bosch craftyf1.

Wb we are only talking about 3 active components here worth over half the value of the saw, and one of those being new speed control I’d hate to just shotgun it with a new field and armature. Those are all the details I can think of.

The only way to find it will be to disassemble the saw and inspect the bearings.

Bosch Table Saw | |

The windings look a little discolored but not fried. Been buying parts but never used the Forum, so here goes, Customer called and said that his Bosch started tripping his breakers in the shop and the motor is struggling also running 40000 Hi gettes,No you should just be able to take the brushes out and remove the wbf screws that hold the motor housing to sfb front bearing housing and slide the housing off the armature.

Thank you all for the great information. A piece of wood got crooked and bound up for less than a second before I threw the switch off. I have the saw upside down on an assembly bench. What does this board do and can I bypass it? We 400 always found the problem to be with the field. Also when I tilt the blade to cut a 45, the blade hits the lower bar underneath the table when I start it up?


A picture should have been taken. Lately I’ve been hearing this squealing noise when the saw is running and when I shut it off. I would hate to replace the armature only to later need to replace the field only later to replace something else. My lock bisch the blade positioning is not working. I cannot get them assembled. I then shut it off but it never turned back on.

It still will not run. Hello rayjavu, The part number for the complete blade guard assembly is There are various adapters commonly available that will adapt from the 2. Or does this sound like it could be the speed control chip, since the 4000 on startup seems to be much higher than normal?

I haven’t found this specific issue in the forum and am in the process of disassembly which may reveal the problem but if anyone has some insight it would be greatly appreciated. And the brushes get really hot very quick.

I am guessing that it is currently bpsch too tight so the clamp can’t lock.

Switch is fine, and the armature looks fine as well as the brushes and commutater. I hope this helps in this case,good luck. Noticed I had an outlet within 400 of the saw cord and figured whats the harm, right? Hope that helps, WJA. Bosch had some quality control issues with the controllers but my understanding is this is in the past.

Anyone with similar experiences?

If you have any play where the bearings seat I would think that would be the cause of your problems. The motor now sounds forced and is running in opposite direction. I took off the plastic brush screws but found the inner connector with a cable connection. What is a good table top circular saw. When the motor is running slow do you hear any sounds like bacon frying?


Bosch WFB Series; Homark; Siemens WM Series Drain Pump Base & Filter Housing (220V-240V, 50Hz, 30W)

Is there any way to determine that or do I just have to start ordering parts until the saw works? Now, by looking at the parts drawing, it definetely seems as though bearings are bad, but, there is also a gear in the front of the motor.

I can not figure out how to remove the primary shaft from the old broken piece to install in new part. What do the brushes look like? Hi Brad, Sorry to hear about your saw. I have a Bosch table saw that has stop working. You really don’t need to replace the larger front armature bearing as this almost never goes bad.

It tends to sieze up. Bosch – Defective Motor keith. That bearing was fine. Hi, No don’t bypass the controller. It was fine for 5 years.

Burned out motors are a common problem with table saws, often because people push material through the saw too quickly. Hi Joalmorris, based on what you tell me I can’t think what else it could be.

A loud noise is usually caused by bad bosvh. Hello thominkentuck, If you pull the parts diagram by clicking on the model Bosch below and find item number 12 you will be able to get an idea on where the speed control is located. Now I’m faced bosvh a repair cost that exceeds what I can get an entire cheap chinese saw for