Z Motorcycle. Service Manual. All rights reserved. No parts of this publication may be reproduced, stored in a retrieval system, 25, (K) To protect the environment in which we all live, Kawasaki has incorporated crankcase emis-. top > Search for Owner’s Manual (Motorcycle). How to use this service. , , , , , , , , , , , , , . KAWASAKI Z REPAIR MANUAL DOWNLOAD This is the COMPLETE factory service workshop repair manual printed for the KAWASAKI Z
|Published (Last):||9 February 2013|
|PDF File Size:||6.89 Mb|
|ePub File Size:||9.18 Mb|
|Price:||Free* [*Free Regsitration Required]|
Tight the bolt to the specified torque with the stopper for turning prevention applied.
Tachometer [A] If the idle speed is out of the specified range, adjust it. ECU Fuse Installation If a fuse fails during operation, inspect the DFI system to determine the cause, and then replace it with a new fuse of proper amperage. This is to set the screw to its original position.
Download Manual: 2003 Kawasaki Z1000 — Owner’s Manual
Separator breather hose blue 4. Pickup coil and oil pressure switch 8. Torque – Front Axle: Engine harness Connect the harness on the cross pipe. Connecting rod bend – – – TIR 0. Radial – – – TIR 0.
Kawasaki Z – Owner’s Manual – Pages – PDF
Pull the bulb out to prevent damage to the bulb. Make sure the area is well-ventilated and free from any source of flame or sparks; Throttle Vacuum Pressure manjal ST: Place a strip on each journal parallel to the camshaft installed in the correct position.
Joint Connector C 8. Front Fender see Frame chapter. If the fan does not rotate, inspect the following.
Do not touch the spark plugs or stick coils while ownsrs engine is running, or you could receive a severe electrical shock. Press down evenly with both hands. Apply soap and water solution or rubber lubricant. Joint Connector B Install the exterior of the lead with staking area facing downward.
Kawasaki Z1000 Service Manual
Never drop the sensor, especially on a hard surface. Cooling reserve tank hose 6. Apply silicone sealant to the alternator lead grommet and crankcase halves mating surface [A] on the front and rear sides of the cover mount.
Throttle Sensor Resistance Connections: Engine Stop Switch d. Table of Contents Add to my manuals Add. No valve clearance Adjust see chapter 2.
Engine Oil Flow Chart Inlet air temperature sensor trouble Inspect and replace see chapter 3. In these models, the head- light does not go on when the ignition switch and the engine stop switch are first turned on. Clutch Lever Mabual Play – – – Clutch: Never reverse the connections of the battery, this could damage the ECU. All 0203 contained in this publication is based on the latest product information available at the time of publication.
Special Tool – Bearing Driver Set: If all other starter motor and starter motor circuit components check good, but the starter motor still does not turn over or only turns over weakly, replace the starter motor with a new one.
Can Kawasaki’s all-new speedster challenge Yamaha’s longstanding naked-class dominance? Replace the caliper if the cylinder and piston are badly scores or rusty. Bend the bracket as shown to secure the 200.
Flywheel and Pulley Holder: Atmospheric pressure sensor trouble Inspect see chapter 3. Replace the O-rigs of the indicators. Then push and turn it further in the same direction and remove the cap. Axial – – – TIR 0.
Owner’s Manuals & Service Manuals | Kawasaki Vehicles
Engine Stop Switch pump an injectors k. CAUTION To avoid damaging the electrical connections in- side the switch, be sure that the kawasami body does not turn during adjustment. Throttle Full Open Pv: Apply a non-permanent locking agent.
If the teeth are worn as illustrated, replace the sprocket, and inspect the drive chain wear see Drive Chain Wear Inspection.